|
AASHTO LRFD U.S. ERTA |
AASHTO LRFD Bridge Design Specifications - Customary U.S. Units |
|
AASHTO HB-17 |
Standard Specifications for Highway Bridges-17th Edition; Errata 01/2003; Errata: 03/2005 |
|
HB-17 |
Standard Specifications for Highway Bridges-17th Edition; Errata 01/2003; Errata: 03/2005 |
|
AASHTO LRFD SI ERTA |
AASHTO LRFD Bridge Design Specifications - SI Units |
|
AASHTO BWC-4 |
Bridge Welding Code-AWS D1.5M/D1.5; Interim 2003; Interim 2005 |
|
AASHTO GDHS-5 |
Policy on Geometric Design of Highways and Streets-Fifth Edition |
|
AASHTO T 209 |
Standard Method of Test for Theoretical Maximum Specific Gravity and Density of Hot-Mix Asphalt Paving Mixtures |
|
AASHTO T 27 |
Standard Method of Test for Sieve Analysis of Fine and Coarse Aggregates-ASTM Designation: C 136-05 |
|
AASHTO LRFD-CONS AMD |
AASHTO LRFD Bridge Construction Specifications-Second Edition |
|
AASHTO T 166 |
Standard Method of Test for Bulk Specific Gravity of Compacted Hot-Mix Asphalt Using Saturated Surface-Dry Specimens |
|
AASHTO PS |
AASHTO Provisional Standards |
|
AASHTO APPENDICES |
Appendices to Standard Specifications for Highway Bridges 2002-17th Edition |
|
AASHTO T 180 |
Standard Method of Test for Moisture-Density Relations of Soils Using a 4.54-kg (10-lb) Rammer and a 457-mm (18-in.) Drop |
|
AASHTO T 99 |
Standard Method of Test for the Moisture-Density Relations of Soils Using a 2.5-kg (5.5-lb) Rammer and a 305-mm (12-in.) Drop |
|
AASHTO T 22 |
Standard Method of Test for Compressive Strength of Cylindrical Concrete Specimens-ASTM Designation: C 39-04a |
|
AASHTO GDPS-4 |
Guide for Design of Pavement Structures |
|
AASHTO M 294 |
Standard Specification for Corrugated Polyethylene Pipe, 300- to 1500-mm Diameter |
|
AASHTO HB-17 TOC |
Standard Specifications for Highway Bridges-17th Edition; Errata: 01/2003; Errata: 03/2005 |
|
AASHTO M 85 |
Standard Specification for Portland Cement-ASTM Designation: C 150-04a |
|
AASHTO T 11 |
Standard Method of Test for Materials Finer Than 75-um (No. 200) Sieve in Mineral Aggregates by Washing-ASTM Designation: C 117-03 |
|
AASHTO T 84 |
Standard Method of Test for Specific Gravity and Absorption of Fine Aggregate-ASTM Designation: C 128-97 |
|
AASHTO CM-4 |
Construction Manual for Highway Construction-Fourth Edition |
|
AASHTO T 308 |
Standard Method of Test for Determining the Asphalt Binder Content of Hot-Mix Asphalt (HMA) by the Ignition Method |
|
AASHTO R 18 |
Standard Recommended Practice for Establishing and Implementing a Quality System for Construction Materials Testing Laboratories |
|
AASHTO T 85 |
Standard Method of Test for Specific Gravity and Absorption of Coarse Aggregate-ASTM Designation: C 127-88 (1993) |
|
AASHTO RSDG-3 |
Roadside Design Guide-Appendix A Revision; Errata: 12/2004 |
|
AASHTO T 88 |
Standard Method of Test for Particle Size Analysis of Soils |
|
AASHTO CHBTW |
Construction Handbook for Bridge Temporary Works |
|
AASHTO T 312 |
Standard Method of Test for Preparing and Determining the Density of Hot-Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor |
|
AASHTO LTS-4 |
Standard Specifications for Structural Supports for Highway Signs, Luminaires and Traffic Signals-Fourth Edition; Interim 2002; Interim 2003 |
|
LTS-4 |
Standard Specifications for Structural Supports for Highway Signs, Luminaires and Traffic Signals-Fourth Edition; Interim 2002; Interim 2003 |
|
AASHTO M 145 |
Standard Specifications for Classification of Soils and Soil-Aggregate Mixtures for Highway Construction Purposes |
|
AASHTO T 2 |
Standard Method of Test for Sampling of Aggregates-HM-22; Part IIA; ASTM Designation D 75-87(1992)E1 |
|
AASHTO T 89 |
Standard Method of Test for Determining the Liquid Limit of Soils-HM-22; Part IIA |
|
AASHTO M 181 |
Standard Specification for Chain-Link Fence |
|
AASHTO T 90 |
Standard Method of Test for Determining the Plastic Limit and Plasticity Index of Soils |
|
AASHTO LRFR |
GUIDE MANUAL FOR CONDITION EVALUATION AND LOAD AND RESISTANCE FACTOR RATING (LRFR) OF HIGHWAY BRIDGES-Revised cover sheet; Interim 2005 |
|
AASHTO M 295 |
Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use in Concrete-ASTM Designation: C 618-03 |
|
AASHTO M 36 |
Standard Specification for Corrugated Steel Pipe, Metallic-Coated, for Sewers and Drains-ASTM Designation: A 760/A 760M-01a |
|
AASHTO HM-26 |
Standard Specifications for Transportation Materials and Methods of Sampling and Testing-26th Edition; Part IA & Part IB; Part IIA & Part IIB; Includes PS 2006 |
|
AASHTO M 288 |
Standard Specification for Geotextile Specification for Highway Applications |
|
AASHTO M 252 |
Standard Specification for Corrugated Polyethylene Drainage Pipe |
|
AASHTO M 164 |
Standard Specification for High-Strength Bolts for Structural Steel Joints-ASTM Designation: A 325-04b |
|
AASHTO M 270M/M 270 |
Standard Specification for Structural Steel for Bridges-ASTM Designation: A 709/A 709M-05 |
|
AASHTO T 176 |
Standard Method of Test for Plastic Fines in Graded Aggregates and Soils by Use of the Sand Equivalent Test-HM-22; Part IIA |
|
AASHTO T 283 |
Standard Method of Test for Resistance of Compacted Asphalt Mixtures to Moisture-Induced Damage |
|
AASHTO GSCB-2 |
Guide Specifications for Design and Construction of Segmental Concrete Bridges-Second Edition; Interim 2003 |
|
AASHTO T 100 |
Standard Method of Test for Specific Gravity of Soils-ASTM Designation: D 854-00 |
|
AASHTO T 19M/T 19 |
Standard Method of Test for Bulk Density ( Unit Weight ) and Voids in Aggregate-ASTM Designation: C 29/C 29M-97 (2003) |
|
AASHTO T 96 |
Standard Method of Test for Resistance to Degradation of Small-Size Coarse Aggregate by Abrasion and Impact in the Los Angeles Machine-HM-22; Part IIA; ASTM Designation C 131-01 |
|
AASHTO M 323 |
Standard Specification for Superpave Volumetric Mix Design |
|
AASHTO T 23 |
Standard Method of Test for Making and Curing Concrete Test Specimens in the Field-ASTM Designation: C 31-03a |
|
AASHTO T 30 |
Standard Method of Test for Mechanical Analysis of Extracted Aggregate |
|
AASHTO T 87 |
Standard Method of Test for Dry Preparation of Disturbed Soil and Soil Aggregate Samples for Test |
|
AASHTO GHC-4 |
AASHTO Guide Specification for Horizontally Curved Steel Girder Highway Bridges - With Design Examples for I-Girder and Box-Girder Bridges-Errata: 10/2003 |
|
AASHTO T 304 |
Standard Method of Test for Uncompacted Void Content of Fine Aggregate |
|
AASHTO T 193 |
Standard Method of Test for the California Bearing Ratio |
|
AASHTO FIM-2 |
Manual on Foundation Investigations |
|
AASHTO M 231 |
Standard Specification for Weighing Devices Used in the Testing of Materials |
|
AASHTO M 92 |
Standard Specification for Wire-Cloth Sieves for Testing Purposes-ASTM Designation: E 11-04 |
|
AASHTO T 59 |
Standard Method of Test for Testing Emulsified Asphalts-HM-22; Part IIA; ASTM Designation D 244-95 |
|
AASHTO T 224 |
Standard Method of Test for Correction for Coarse Particles in the Soil Compaction Test |
|
AASHTO M 170 |
Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe-ASTM Designation: C 76-05 |
|
AASHTO M 232M/M 232 |
Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware-ASTM Designation: A 153/A 153M-05 |
|
AASHTO M 43 |
Standard Specification for Sizes of Aggregate for Road and Bridge Construction-ASTM Designation: D 448-03a |
|
AASHTO T 315 |
Standard Method of Test for Determining the Rheological Properties of Asphalt Binder Using a Dynamic Shear Rheometer (DSR) |
|
AASHTO T 152 |
Standard Method of Test for Air Content of Freshly Mixed Concrete by the Pressure Method-ASTM Designation: C 231-03 |
|
AASHTO RSDG CHAPTER 6 |
Roadside Design Guide Chapter Six Update |
|
AASHTO T 106M/T 106 |
Standard Method of Test for Compressive Strength of Hydraulic Cement Mortar (Using 50-mm or 2-in. Cube Specimens)-ASTM Designation C 109/C 109M-02 |
|
AASHTO T 265 |
Standard Method of Test for Laboratory Determination of Moisture Content of Soils |
|
AASHTO M 251 |
Standard Specification for Plain and Laminated Elastomeric Bridge Bearings |
|
AASHTO M 31M/M 31 |
Standard Specification for Deformed and Plain Carbon-Steel Bars for Concrete Reinforcement-ASTM Designation: A 615/A 615M-05 |
|
AASHTO T 121M/T 121 |
Standard Method of Test for Density (Unit Weight), Yield, and Air Content (Gravimetric) of Concrete-ASTM Designation: C 138/C 138M-01a |
|
AASHTO MCEB-2 |
Manual for Condition Evaluation of Bridges-Second Edition; Includes Interim Specifications: 1995, 1996, 1998, 2000, 2001, and 2003 |
|
AASHTO T 168 |
Standard Method of Test for Sampling Bituminous Paving Mixtures-ASTM Designation: D 979-01 |
|
AASHTO T 24 |
Standard Method of Test for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete-ASTM Designation: C 42-04 |
|
AASHTO COMMENTARIES |
Commentaries to Standard Specifications for Highway Bridges 2002-17th Edition |
|
AASHTO GSDPB |
Guide Specifications for Design of Pedestrian Bridges |
|
AASHTO M 183M/M 183 |
Standard Specification for Structural Steel-Twentieth Edition; ASTM A36/A36M-96; Discontinued |
|
AASHTO M 194M/M 194 |
Standard Specification for Chemical Admixtures for Concrete |
|
AASHTO M 247 |
Standard Specification for Glass Beads Used in Traffic Paints |
|
AASHTO T 104 |
Standard Method of Test for Soundness of Aggregate by Use of Sodium Sulfate or Magnesium Sulfate |
|
AASHTO M 314 |
Standard Specification for Steel Anchor Bolts |
|
AASHTO T 49 |
Standard Method of Test for Penetration of Bituminous Materials-ASTM Designation: D 5-05a |
|
AASHTO M 111M/M 111 |
Standard Specification for Zinc (Hot-Dip Galvanized) Coatings on Iron and Steel Products-ASTM Designation: A 123/A 123M-02 |
|
AASHTO T 164 |
Standard Method of Test for Quantitative Extraction of Asphalt Binder from Hot-Mix Asphalt (HMA)-ASTM Designation: D 2172-01 |
|
AASHTO LRFD-MOV |
AASHTO LRFD Movable Highway Bridge Design Specifications-Second Edition |
|
AASHTO T 248 |
Standard Method of Test for Reducing Samples of Aggregate to Testing Size-ASTM Designation: C 702-98 (2003) |
|
AASHTO T 227 |
Standard Method of Test for Density, Relative Density (Specific Gravity), or API Gravity of Crude Petroleum and Liquid Petroleum Products by Hydrometer Method-HM-22; PART IIB; ASTM D 1298-99 |
|
AASHTO T 245 |
Standard Method of Test for Resistance to Plastic Flow of Bituminous Mixtures Using Marshall Apparatus |
|
AASHTO M 180 |
Standard Specification for Corrugated Sheet Steel Beams for Highway Guardrail |
|
AASHTO GSBTW |
Guide Design Specifications for Bridge Temporary Works |
|
AASHTO M 320 |
Standard Specification for Performance-Graded Asphalt Binder |
|
AASHTO T 316 |
Standard Method of Test for Viscosity Determination of Asphalt Binder Using Rotational Viscometer |
|
AASHTO M 80 |
Standard Specification for Coarse Aggregate for Portland Cement Concrete |
|
AASHTO HM-26 PT II |
Standard Specifications for Transportation Materials and Methods of Sampling and Testing Part II: Tests-26th Edition; Includes Part IIA and Part IIB |
|
AASHTO T 288 |
Standard Method of Test for Determining Minimum Laboratory Soil Resistivity |
|
AASHTO T 313 |
Standard Method of Test for Determining the Flexural Creep Stiffness of Asphalt Binder Using the Bending Beam Rheometer (BBR) |
|
AASHTO R 30 |
Standard Practice for Mixture Conditioning of Hot-Mix Asphalt (HMA) |
|
AASHTO M 240 |
Standard Specification for Blended Hydraulic Cement-ASTM Designation: C 595-03 |
|
AASHTO T 301 |
Standard Method of Test for Elastic Recovery Test of Bituminous Materials by Means of a Ductilometer |
|
AASHTO T 310 |
Standard Specification for In-Place Density and Moisture Content of Soil and Soil-Aggregate by Nuclear Methods (Shallow Depth) |
|
AASHTO M 157 |
Standard Specification for Ready-Mixed Concrete |
|
AASHTO M 307 |
Standard Specification for Silica Fume Used in Cementitious Mixtures-ASTM Designation: C 1240-03a |
|
AASHTO T 277 |
Standard Method of Test for Electrical Indication of Concrete s Ability to Resist Chloride Ion Penetration-ASTM Designation: C 1202-94 |
|
AASHTO GL-6 |
Roadway Lighting Design Guide |
|
AASHTO M 190 |
Standard Specification for Bituminous Coated Corrugated Metal Culvert Pipe and Pipe Arches |
|
AASHTO T 21 |
Standard Method of Test for Organic Impurities in Fine Aggregates for Concrete-ASTM Designation: C 40-04 |
|
AASHTO M 284M/M 284 |
Standard Specification for Epoxy-Coated Reinforcing Bars: Materials and Coating Requirements-ASTM Designation A 775/A 775M-04a |
|
AASHTO M 6 |
Standard Specification for Fine Aggregate for Portland Cement Concrete |
|
AASHTO MM-3 |
Maintenance Manual: The Maintenance and Management of Roadways and Bridges |
|
AASHTO R 35 |
Standard Practice for Superpave Volumetric Design for Hot-Mix Asphalt (HMA) |
|
AASHTO T 267 |
Standard Method of Test for Determination of Organic Content in Soils by Loss on Ignition |
|
AASHTO LRFD I-GIRDER |
AASHTO-LRFD DESIGN EXAMPLE HORIZONTALLY CURVED STEEL I-GIRDER BRIDGE - FINAL REPORT |
|
AASHTO M 291 |
Standard Specification for Carbon and Alloy Steel Nuts-ASTM Designation A 563-04a |
|
AASHTO M 55M/M 55 |
Standard Method of Test for Steel Welded Wire Reinforcement, Plain, for Concrete-ASTM Designation: A 185-02 |
|
AASHTO T 105 |
Standard Method of Test for Chemical Analysis of Hydraulic Cement-ASTM Designation: C 114-05 |
|
AASHTO T 48 |
Standard Method of Test for Flash and Fire Points by Cleveland Open Cup-ASTM Designation: D 92-05a |
|
AASHTO ALFD-2 |
Guide Specifications for Alternate Load Factor Design Procedures for Steel Beam Bridges Using Braced Compact Sections-Revised per Interim Specifications - Bridges - 1994 |
|
AASHTO T 190 |
Standard Method of Test for Resistance R-Value and Expansion Pressure of Compacted Soils-HM-22; Part IIA; ASTM Designation: D 2844-69(1975) |
|
AASHTO T 191 |
Standard Method of Test for Density of Soil In-Place by the Sand-Cone Method |
|
AASHTO M 160M/M 160 |
Standard Specification for General Requirements for Steel Plates, Shapes, Sheet Piling, and Bars for Structural Use-ASTM Degsignation: A 6/A 6M-05 |
|
AASHTO T 201 |
Standard Method of Test for Kinematic Viscosity of Asphalts (Bitumens)-ASTM Designation D 2170-01a |
|
AASHTO T 290 |
Standard Method of Test for Determining Water-Soluble Sulfate Ion Content in Soil |
|
AASHTO T 303 |
Standard Method of Test for Accelerated Detection of Potentially Deleterious Expansion of Mortar Bars Due to Alkali-Silica Reaction |
|
AASHTO GBF-3 |
Guide for the Development of Bicycle Facilities |
|
AASHTO HDG |
Highway Drainage Guidelines-4th edition |
|
AASHTO M 213 |
Standard Specification for Preformed Expansion Joint Fillers for Concrete Paving and Structural Construction (Nonextruding and Resilient Bituminous Types)-ASTM Designation D 1751-99 |
|
AASHTO M 300 |
Standard Specification for Inorganic Zinc-Rich Primer |
|
AASHTO T 240 |
Standard Method of Test for Effect of Heat and Air on a Moving Film of Asphalt (Rolling Thin-Film Oven Test)-ASTM Designation D 2872-04 |
|
AASHTO T 40 |
Standard Method of Test for Sampling Bituminous Materials-HM-22; Part IIA; ASTM Designation D 140-00 |
|
AASHTO M 173 |
Standard Specification for Concrete Joint-Sealer, Hot-Poured Elastic Type-ASTM Designation: D1190-97; No Replacment |
|
AASHTO T 215 |
Standard Method of Test for Permeability of Granular Soils (Constant Head)-ASTM 2434-68(1994)E1 |
|
AASHTO T 269 |
Standard Method of Test for Percent Air Voids in Compacted Dense and Open Bituminous Paving Mixtures-ASTM Designation D 3203-94 (2000) |
|
AASHTO M 156 |
Standard Specification for Requirements for Mixing Plants for Hot-Mixed, Hot-Laid Bituminous Paving Mixtures-ASTM Designation: D995-95b |
|
AASHTO M 254 |
Standard Specification for Corrosion-Resistant Coated Dowel Bars |
|
AASHTO NTCIP 2001 |
National Transportation Communications for ITS Protocol-Class B Profile-Formerly Numbered NEMA TS 3.3-1996; A Joint Standard of AASHTO, ITE, and NEMA |
|
ITE NTCIP 2001 |
National Transportation Communications for ITS Protocol-Class B Profile-Formerly Numbered NEMA TS 3.3-1996; A Joint Standard of AASHTO, ITE, and NEMA |
|
NEMA NTCIP 2001 |
National Transportation Communications for ITS Protocol-Class B Profile-Formerly Numbered NEMA TS 3.3-1996; A Joint Standard of AASHTO, ITE, and NEMA |
|
AASHTO T 216 |
Standard Method of Test for One-Dimensional Consolidation Properties of Soils-ASTM Designation D 2435-90 |
|
AASHTO T 255 |
Standard Method of Test for Total Ecaparable Moisture Content of Aggregate by Drying-ASTM Designation: C 566-97 (2004) |
|
AASHTO T 51 |
Standard Method of Test for Ductility of Bituminous Materials-ASTM Designation: D 113-99 |
|
AASHTO VLVLR-1 |
Guidelines for Geometric Design of Very Low-Volume Local Roads (ADT Less Than or Equal to 400)-Errata: 08/2002 |
|
AASHTO HM-26 PT I |
Standard Specifications for Transportation Materials and Methods of Sampling and Testing Part I: Specifications-26th Edition; Includes Part IA and Part IB |
|
AASHTO M 32M/M 32 |
Standard Method of Test for Steel Wire, Plain, for Concrete Reinforcement-ASTM Designation: A 82-02 |
|
AASHTO R 11 |
Standard Recommended Practice for Indicating Which Places of Figures Are to Be Considered Significant in Specified Limiting Values-ASTM Designation: E 29-04 |
|
AASHTO T 134 |
Standard Method of Test for Moisture-Density Relations of Soil-Cement Mixtures |
|
AASHTO T 275 |
Standard Method of Tests for Bulk Specific Gravity of Compacted Bituminous Mixtures Using Paraffin-Coated Specimens |
|
AASHTO CORE |
Commonly Recognized (CoRe) Structural Elements-2002 Interim Revision |
|
AASHTO HB-17 DIVISION II SEC 22 |
Division II Construction - Slope Protection |
|
AASHTO LRFD BOX GIRDER |
AASHTO-LRFD DESIGN EXAMPLE HORIZONTALLY CURVED STEEL BOX GIRDER BRIDGE - FINAL REPORT |
|
AASHTO M 153 |
Standard Specification for Preformed Sponge Rubber and Cork Expansion Joint Fillers for Concrete Paving and Structural Construction-ASTM Designation D 1752-04a |
|
AASHTO M 306 |
Standard Specification for Drainage, Sewer, Utility, and Related Castings |
|
AASHTO R 9 |
Standard Recommended Practice for Acceptance Sampling Plans for Highway Construction |
|
AASHTO T 119M/T 119 |
Standard Method of Test for Slump of Hydraulic Cement Concrete-ASTM Designation: C 143/C 143M-03 |
|
AASHTO T 260 |
Standard Method of Test for Sampling and Testing for Chloride Ion in Concrete and Concrete Raw Materials |
|
AASHTO T 53 |
Standard Method of Test for Softening Point of Bitumen (Ring-and-Ball Apparatus)-ASTM Designation: D 36-95 (2000)e1 |
|
AASHTO M 199 |
Standard Specification for Precast Reinforced Concrete Manhole Sections-ASTM Designation: C 478-03a |
|
AASHTO M 201 |
Standard Specification for Mixing Rooms, Moist Cabinets, Moist Rooms, and Water Storage Tanks Used in the Testing of Hydraulic Cements and Concretes-ASTM Designation: C 511-05 |
|
AASHTO M 259 |
Standard Specification for Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers-ASTM Designation: C 789-95a |
|
AASHTO M 278 |
Standard Specification for Class PS46 Poly(Vinyl Chloride) (PVC) Pipe-HM-22; Part IB |
|
AASHTO T 231 |
Standard Method of Test for Capping Cylindrical Concrete Specimens-ASTM Designation C 617-98 (2003) |
|
AASHTO T 26 |
Standard Method of Test for Quality of Water to Be Used in Concrete |
|
AASHTO T 97 |
Standard Method of Test for Flexural Strength of Concrete (Using Simple Beam with Third-Point Loading)-ASTM Designation C 78-02 |
|
AASHTO GSSB |
Guide Specifications for Structural Design of Sound Barriers-Interim Specifications: 1992, 2002 |
|
AASHTO HM-26 PT I TOC |
Standard Specifications for Transportation Materials and Methods of Sampling and Testing Part I: Specifications-26th Edition; Includes Table of Contents for Part IA and Part IB |
|
AASHTO M 105 |
Standard Specification for Gray Iron Castings |
|
AASHTO M 140 |
Standard Specification for Emulsified Asphalt-ASTM Designation D 977-98 |
|
AASHTO M 280 |
Standard Specification for Metallic-Coated Carbon Steel Barbed Wire-ASTM Designation A 121-99 |
|
AASHTO T 196M/T 196 |
Standard Method of Test for Air Content of Freshly Mixed Concrete by the Volumetric Method-ASTM Designation ASTM C 173/C 173M-01 |
|
AASHTO T 202 |
Standard Method of Test for Viscosity of Asphalts by Vacuum Capillary Viscometer-ASTM Designation D 2171-01 |
|
AASHTO T 327 |
Standard Method of Test for Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus-ASTM Designation: D 6928-03 |
|
AASHTO HB-17 DIVISION I SEC 4 |
Division I Design - Foundations-(Part A, Part B, and Part C); Errata 01/2003 |
|
AASHTO M 198 |
Standard Specification for Joints for Concrete Pipe, Manholes, and Precast Box Sections Using Preformed Flexible Joint Sealants-ASTM Designation: C 990-03a |
|
AASHTO MP2 |
Standard Specification for Superpave Volumetric Mix Design-2000 Edition; Interim Edition 4/2001 |
|
MP2 |
Standard Specification for Superpave Volumetric Mix Design-2000 Edition; Interim Edition 4/2001 |
|
AASHTO T 236 |
Standard Method of Test for Direct Shear Test of Soils under Consolidated Drained Conditions-ASTM Designation D 3080-72(1979) |
|
AASHTO M 133 |
Standard Specification for Preservatives and Pressure Treatment Processes for Timber |
|
AASHTO M 148 |
Standard Specification for Liquid Membrane-Forming Compounds for Curing Concrete-ASTM Designation: C 309-03 |
|
AASHTO T 210 |
Standard Method of Test for Aggregate Durability Index-ASTM Designation D 3744-03 |
|
AASHTO TP 69 |
Standard Method of Test for Bulk Specific Gravity and Density of Compacted Asphalt Mixtures Using Automatic Vacuum Sealing Method-ASTM Designation D: 6752-02a |
|
AASHTO GDPS-3 V2 |
Guide for Design of Pavement Structures Volume 2-Supplement - 1998 |
|
AASHTO HB-17 DIVISION I SEC 3 |
Division I Design - Loads-(Part A, Part B, and Part C); Errata 01/2003 |
|
AASHTO M 208 |
Standard Specification for Cationic Emulsified Asphalt-HM-22; Part IA; ASTM Designation D 2397-98 |
|
AASHTO M 226 |
Standard Specification for Viscosity-Graded Asphalt Cement |
|
AASHTO M 302 |
Standard Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars-ASTM Designation: C 989-05 |
|
AASHTO M 304 |
Standard Specification for Poly(Vinyl Chloride) (PVC) Profile Wall Drain Pipe and Fittings Based on Controlled Inside Diameter |
|
AASHTO T 228 |
Standard Method of Test for Specific Gravity of Semi-Solid Bituminous Materials-ASTM Designation: D 70-03 |
|
AASHTO T 291 |
Standard Method of Test for Determining Water-Soluble Chloride Ion Content in Soil |
|
AASHTO T 72 |
Standard Method of Test for Saybolt Viscosity-HM-22; Part IIA; ASTM Designation D 88-94(1999) |
|
AASHTO HM-26 PT II TOC |
Standard Specifications for Transportation Materials and Methods of Sampling and Testing Part II Tests-26th Edition; Includes Table of Contents for Part IIA and Part IIB |
|
AASHTO M 154 |
Standard Specification for Air-Entraining Admixtures for Concrete-ASTM Designation C 260-01 |
|
AASHTO M 171 |
Standard Specification for Sheet Materials for Curing Concrete-ASTM Designation: C171-03 |
|
AASHTO M 195 |
Standard Specification for Lightweight Aggregates for Structural Concrete-Twentieth Edition; ASTM C330-04 |
|
AASHTO T 141 |
Standard Method of Test for Sampling Freshly Mixed Concrete-ASTM Designation: C 172-04 |
|
AASHTO T 208 |
Standard Method of Test for Unconfined Compressive Strength of Cohesive Soil-ASTM Designation D 2166-00 |
|
AASHTO M 169 |
Standard Specification for Steel Bars, Carbon, and Alloy, Cold-Finished-ASTM Designation: A 108-03 |
|
AASHTO M 17 |
Standard Specification for Mineral Filler for Bituminous Paving Mixtures-ASTM Designation: ASTM D242-95 (2000) |
|
AASHTO PP 49 |
Standard Practice for Certification of Inertial Profiling Systems |
|
AASHTO PP28 |
Standard Practice for Superpave Volumetric Design for Hot Mix Asphalt (HMA)-2000 Edition; Interim Edition 4/2001 |
|
AASHTO T 289 |
Standard Method of Test for Determining pH of Soil for Use in Corrosion Testing |
|
AASHTO T 307 |
Standard Method of Test for Determining the Resilient Modulus of Soils and Aggregate Materials |
|
AASHTO TP4 |
Standard Method for Preparing and Determining the Density of Hot Mix Asphalt (HMA) Specimens by Means of the Superpave Gyratory Compactor-2000 Edition; |
|
AASHTO HB-17 DIVISION I SEC 1 |
Division I Design - General Provisions |
|
AASHTO M 196 |
Standard Specification for Corrugated Aluminum Pipe for Sewers and Drains-ASTM B745/B745M-95 |
|
AASHTO T 192 |
Standard Method of Test for Fineness of Hydraulic Cement by the 45-um (No. 325) Sieve-ASTM Designation C 430-96 |
|
AASHTO T 230 |
Standard Method of Test for Determining Degree of Pavement Compaction of Bituminous Aggregate Mixtures-HM-22; PART IIB |
|
AASHTO T 314 |
Standard Method of Test for Determining the Fracture Properties of Asphalt Binder in Direct Tension (DT) |
|
AASHTO T 44 |
Standard Method of Test for Solubility of Bituminous Materials-ASTM Designation D 2042-01 |
|
AASHTO T 65M/T 65 |
Standard Method of Test for Mass [Weight] of Coating on Iron and Steel Articles with Zinc or Zinc-Alloy Coatings-ASTM Designation: A 90/A 90M-01 |
|
AASHTO TP 60 |
Standard Method of Test for Coefficient of Thermal Expansion of Hydraulic Cement Concrete |
|
AASHTO M 203M/M 203 |
Standard Specification for Steel Strand, Uncoated Seven-Wire for Concrete Reinforcement-ASTM Designation: A 416/A 416M-02 |
|
AASHTO M 81 |
Standard Specification for Cut-Back Asphalt (Rapid-Curing Type) |
|
AASHTO MUTCD-3 PART 2 |
Manual on Uniform Traffic Control Devices - Millennium Edition - Part 2 Signs |
|
AASHTO PP 48 |
Standard Practice for Evaluation of the Superpave Gyratory compactor (SGC) Internal Angle of Gyration |
|
AASHTO R 28 |
Standard Practice for Accelerated Aging of Asphalt Binder Using a Pressurized Aging Vessel (PAV) |
|
AASHTO SS |
AASHTO Salary Survey |
|
AASHTO T 126 |
Standard Method of Test for Making and Curing Concrete Test Specimens in the Laboratory-HM-22; Part IIA; ASTM Designation: C 192/C 192M-95 |
|
AASHTO T 242 |
Standard Method of Test for Frictional Properties of Paved Surfaces Using a Full-Scale Tire-ASTM Designation: E 274-97 |
|
AASHTO T 259 |
Standard Method of Test for Resistance of Concrete to Chloride Ion Penetration-HM-22; PART IIB |
|
AASHTO EAST |
Report on the 1990 European Asphalt Study Tour |
|
AASHTO HB-17 DIVISION I SEC 5 |
Division I Design - Retaining Walls-(Part A, Part B, and Part C); Errata 01/2003 |
|
AASHTO HDG CHAPTER 4 |
HYDRAULIC DESIGN OF CULVERTS-4th edition |
|
AASHTO HDG TOC |
Highway Drainage Guidelines-4th edition |
|
AASHTO M 167M/M 167 |
Standard Specification for Corrugated Steel Structural Plate, Zinc-Coated, for Field-Bolted Pipe, Pipe-Arches, and Arches-ASTM Designation: A 761/A 761M-04 |
|
AASHTO M 20 |
Standard Specification for Penetration-Graded Asphalt Cement |
|
AASHTO M 237 |
Standard Specification for Epoxy-Resin Adhesives for Bonding Traffic Markers to Hardened Portland Cement and Asphalt Concrete |
|
AASHTO M 245 |
Standard Specification for Corrugated Steel Pipe, Polymer-Precoated, for Sewers and Drains-ASTM Designation: A 762/A 762M-98 |
|
AASHTO M 248 |
Standard Specification for Ready-Mixed White and Yellow Traffic Paints |
|
AASHTO M 249 |
Standard Specification for White and Yellow Reflective Thermoplastic Striping Material (Solid Form) |
|
AASHTO M 277 |
Standard Specification for Wire Rope and Sockets for Movable Bridges-HM-22; Part IB |
|
AASHTO M 30 |
Standard Specification for Zinc-Coated Steel Wire Rope and Fittings for Highway Guardrail-HM-22; PART IA; ASTM Designation: A 741-98 |
|
AASHTO MDM-3 |
Model Drainage Manual (U.S. and SI Units) |
|
AASHTO R 10 |
Standard Recommended Practice for Definition of Terms Related to Quality and Statistics As Used in Highway Construction |
|
AASHTO T 42 |
Standard Method of Test for Preformed Expansion Joint Filler for Concrete Construction-ASTM Designation D 545-99 |
|
AASHTO 511NPR-1 |
511 National Progress Report |
|
AASHTO DS |
A POLICY ON DESIGN STANDARDS INTERSTATE SYSTEM-Edition 5 |
|
AASHTO INDEX |
Index to Standard Specifications for Highway Bridges 2002-17th Edition |
|
AASHTO M 147 |
Standard Specification for Materials for Aggregate and Soil-Aggregate Subbase, Base and Surface Courses |
|
AASHTO M 200 |
Standard Specification for Epoxy Protective Coatings |
|
AASHTO M 273 |
Standard Specification for Precast Reinforced Concrete Box Sections for Culverts, Storm Drains, and Sewers with Less Than 2 ft of Cover Subjected to Highway Loadings-ASTM C850-95a |
|
AASHTO M 279 |
Standard Specification for Metallic-Coated, Steel Woven Wire Fence Fabric-ASTM A116-00 |
|
AASHTO M132 |
Standard Specification for Terms Relating to Density and Specific Gravity of Solids, Liquids, and Gases-Twentieth Edition; ASTM E12-70 (1991)E1 |
|
AASHTO R 31 |
Standard Practice for Evaluation of Coating Systems with Zinc-Rich Primers |
|
AASHTO T 113 |
Standard Method of Test for Lightweight Pieces in Aggregate-ASTM Designation: C 123-03 |
|
AASHTO T 162 |
Standard Method of Test for Mechanical Mixing of Hydraulic Cement Pastes and Mortars of Plastic Consistency-ASTM Designation: C 305-99e1 |
|
AASHTO T 182 |
Standard Method of Test for Coating and Stripping of Bitumen-Aggregate Mixtures-ASTM Designation D 1664-80 |
|
AASHTO T 206 |
Standard Method of Test for Penetration Test and Split-Barrel Sampling of Soils-ASTM Designation D 1586-99 |
|
AASHTO T 247 |
Standard Method of Test for Preparation of Test Specimens of Bituminous Mixtures by Means of California Kneading Compactor-HM-22; PART IIB; ASTM D 1561-92 |
|
AASHTO GPF |
Guide for the Planning, Design, and Operation of Pedestrian Facilities |
|
AASHTO M 146 |
Standard Specification for Terms Relating to Subgrade, Soil-Aggregate, and Fill Materials |
|
AASHTO M 86 |
Standard Specification for Concrete Sewer, Storm Drain, and Culvert Pipe-ASTM Designation: C 14-03a |
|
AASHTO T 112 |
Standard Method of Test for Clay Lumps and Friable Particles in Aggregate-ASTM Designation: C 142-97 |
|
AASHTO T 167 |
Standard Method of Test for Compressive Strength of Hot-Mix Asphalt |
|
AASHTO T 37 |
Standard Method of Test for Sieve Analysis of Mineral Filler for Hot-Mix Asphalt-ASTM Designation D 546-99(2005) |
|
AASHTO BRH-2 |
Subcommittee on New Highway Materials Task Force 13 Report a Guide to Standardized Highway Barrier Hardware |
|
AASHTO DIVISION I 11.4 |
Structural Supports for Highway Signs, Luminaires, and Traffic Signals |
|
AASHTO DIVISION I 2.2 |
Standard Highway Clearances - General |
|
AASHTO GD-2 |
A Policy on Geometric Design of Rural Highways-Withdrawn Replaced by AASHTO GDHS |
|
AASHTO M 220 |
Standard Specification for Preformed Polychloroprene Elastomeric Joint Seals for Concrete Pavements-ASTM D2628-91(1998) |
|
AASHTO M 235M/M 235 |
Standard Specification for Epoxy Resin Adhesives-ASTM Designation: C 881-99 |
|
AASHTO M 246 |
Standard Specification for Steel Sheet, Metallic-Coated and Polymer- Precoated, for Corrugated Steel Pipe-ASTM Designation: A 742/A 742M-03 |
|
AASHTO M 275M/M 275 |
Standard Specification for Uncoated High-Strength Steel Bar for Prestressing Concrete-ASTM Designation: A 722/A 722M-05 |
|
AASHTO M 29 |
Standard Specification for Fine Aggregate for Bituminous Paving Mixtures-ASTM Designation: D 1073-94 |
|
AASHTO M223M/M223 |
Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Steels of Structural Quality-HM-22; PART IA; ASTM A572M/A572-94c; (Discontinued) |
|
AASHTO MP 8 |
Standard Specification for Designing Stone Matrix Asphalt (SMA) |
|
AASHTO PP 57 |
Establishing Requirements for and Performing Equipment Calibrations, Standardizations, and Checks |
|
AASHTO T 146 |
Standard Method of Test for Wet Preparation of Disturbed Soil Samples for Test |
|
AASHTO T 153 |
Standard Method of Test for Fineness of Hydraulic Cement by Air Permeability Apparatus-HM-22; Part IIA; ASTM Designation: C 204-00 |
|
AASHTO T 194 |
Standard Method of Test for Determination of Organic Matter in Soils by Wet Combustion |
|
AASHTO T 246 |
Standard Method of Test for Resistance to Deformation and Cohesion of Bituminous Mixtures by Means of Hveem Apparatus-ASTM Designation D1560-81 |
|
AASHTO T 329 |
Standard Method of Test for Moisture Content of Hot-Mix Asphalt (HMA) by Oven Method |
|
AASHTO T 71 |
Standard Method of Test for Effect of Organic Impurities in Fine Aggregate on Strength of Mortar-ASTM Designation C 87-83(1995) |
|
AASHTO DIVISION I 3.4 |
Live Load |
|
AASHTO FHD-1 |
A Guide to Achieving Flexibility in Highway Design |
|
AASHTO GSCBS |
Guide Specifications Thermal Effects in Concrete Bridge Superstructures |
|
AASHTO GSDL |
Guide Specifications for Distribution of Loads for Highway Bridges |
|
AASHTO MP 1A |
Standard Specification for Performance-Graded Asphalt Binder |
|
AASHTO PP 34 |
Standard Practice for Estimating the Cracking Tendency of Concrete |
|
AASHTO T 165 |
Standard Method of Test for Effect of Water on Cohesion of Compacted Bituminous Mixtures-HM-22; Part IIA; ASTM Designation: D 1075-96 |
|
AASHTO T 244 |
Standard Method of Test for Mechanical Testing of Steel Products-ASTM Designation A 370-05 |
|
AASHTO T 305 |
Standard Test Method for Determination of Draindown Characteristics in Uncompacted Asphalt Mixtures |
|
AASHTO T 67 |
Standard Method of Test for Standard Practices for Force Verification of Testing Machines-ASTM Designation: E 4-03 |
|
AASHTO T238 |
Standard Method of Test for Density of Soil and Soil-Aggregate In-Place by Nuclear Methods (Shallow Depth)-HM-22; PART IA; (Discontinued) |
|
AASHTO TP58 |
Standard Test Method for Resistance of Coarse Aggregate to Degradation by Abrasion in the Micro-Deval Apparatus-2000 Edition |
|
AASHTO GSEC |
Guide Specifications for Strength Evaluation of Existing Steel and Concrete Bridges |
|
AASHTO HB-17 DIVISION I SEC 14 |
Division I Design - Bearings-Errata 01/2003 |
|
AASHTO HB-17 DIVISION II SEC 4 |
Division II Construction - Driven Foundation Piles |
|
AASHTO M 170M |
Standard Specification for Reinforced Concrete Culvert, Storm Drain, and Sewer Pipe (Metric)-ASTM Designation: C 76M-05 |
|
AASHTO M 206 |
Standard Specification for Reinforced Concrete Arch Culvert, Storm Drain, and Sewer Pipe (Metric)-ASTM Designation C 506M-05a; Renumbered as M 206M/M 206 |
|
AASHTO M 268 |
Standard Specification for Retroreflective Sheeting for Traffic Control-ASTM Designation: D 4956-04 |
|
AASHTO M 274 |
Standard Specification for Steel Sheet, Aluminum-Coated (Type 2), for Corrugated Steel Pipe |
|
AASHTO M 324 |
Standard Specification for Joint and Crack Sealants, Hot Applied, for Concrete and Asphalt Pavements-ASTM Disgnation: D 6690-01 |
|
AASHTO M 33 |
Standard Specification for Preformed Expansion Joint Filler for Concrete (Bituminous Type)-ASTM D 994-98 |
|
AASHTO MP 11 |
Standard Equipment Specifications for Inertial Profiler |
|
AASHTO MSI |
Manual on Subsurface Investigations-Eighteenth Edition |
|
AASHTO PP 42 |
Standard Practice for Determination of Low-Temperature Performance Grade (PG) of Asphalt Binders |
|
AASHTO SR-3 |
Highway Safety Design and Operations Guide |
|
AASHTO T 107 |
Standard Method of Test for Autoclave Expansion of Portland Cement-ASTM Designation: C 151-00 |
|
AASHTO T 131 |
Standard Method of Test for Time of Setting of Hydraulic Cement by Vicat Needle-ASTM Designation: C 191-04a |