ICC - International Code Council

	ICC IBC International Building Code Buy ICC Collections Online subscriptions to multiple documents on various subjects Info To speak with an IHS Subject Matter Expert call 1-888-752-0334, outside the US/Canada call 303-397-2892. More Top ICC Standards...

ICC IBC - International Building Code

Scope:
The provisions of this code shall apply to the construction, alteration, movement, enlargement, replacement, repair, equipment, use and occupancy, location, maintenance, removal and demolition of every building or structure or any appurtenances connected or attached to such buildings or structures.
The purpose of this code is to establish the minimum requirements to safeguard the public health, safety and general welfare through structural strength, means of egress facilities, stability, sanitation, adequate light and ventilation, energy conservation, and safety to life and property from fire and other hazards attributed to the built environment and to provide safety to fire fighters and emergency responders during emergency operations.

Standards Referenced in the ICC IBC:

• 16 CFR 1000-END - Commercial Practices; Part 1201 - Safety Standard for Architectural Glazing Material, Part 1209 - Interim Safety Standard for Cellulose Insulation, Part 1404 - Cellulose Insulation, Part 1500 - Hazardous Substances and Articles; Administration and Enforcement Regulations, Part 1500.44 - Method for Determining Extremely Flammable and Flammable Solids, Part 1507 - Fireworks Devices, and Part 1630 - Standard for the Surface Flammability of Carpets and Rugs
• 29 CFR 1910 - Labor (1910.1000-End); Part 1910.1000 - Air Contaminants
• 49 CFR 100-185 - Transportation; Part 172 - Hazardous Materials Tables, Special Provisions, Hazardous Materials Communications, Emergency Response Information and Training Requirements, Part 173 - Specification of Transportation of Explosive and Other Dangerous Articles, UN 0335, UN 0336 Shipping Containers
• ANSI A190.1 - Wood Products-Structural Glued Laminated Timber
• AITC 104 - Typical Construction Details
• AITC 110 - Standard Appearance Grades for Structural Glued Laminated Timber
• AITC 112 - Standard for Tongue-and-Groove Heavy Timber Roof Decking
• AITC 113 - Standard for Dimensions of Structural Glued Laminated Timber
• AITC 117 - Structural Glued Laminated Timber of Softwood Species
• AITC 119 - Standard Specifications for Structural Glued Laminated Timber of Hardwood Species
• AITC 200 - Inspection Manual for Structural Glued Laminated Timber
• AITC 500 - Determination of Design Values for Structural Glued Laminated Timber
• ALI ALCTV - Standard for Automotive Lifts-Safety Requirements for Construction, Testing and Validation
• ANSI A13.1 - Scheme for the Identification of Piping Systems
• ANSI A108.1 - Installation of Ceramic Tile *** Includes ANSI A108 .1A-C, 108.4 -.13, A118.1-.10, ANSI A136.1
• ANSI A137.1 - American National Standard Specifications for Ceramic Tile
• ANSI A 208.1 - Particleboard
• APA PS 1 - U.S. Product Standard for Construction & Industrial Ply
• ASABE EP 484 - Diaphragm Design of Metal-Clad, Post-Frame Rectangular Buildings
• ASABE EP 486.1 - Shallow-Post Foundation Design
• ASABE EP 559 - Design Requirements and Bending Properties for Mechanically Laminated Columns
• ASCE 5 -Building Code Requirements for Masonry Structures
• ACSE 6 -Specifications for Masonry Structures
• ASCE 7 -Minimum Design Loads for Buildings and Other Structures
• ASCE 8 - Standard Specification for the Design of Cold-Formed Stainless Steel Structural Members
• ASCE 16 - Standard for Load Resistance Factor Design (LRFD) for Engineered Wood Construction.
• ASCE 24 - Flood Resistant Design and Construction
• ASCE 29-99 - Standard Calculation Methods for Structural Fire Protection
• ASCE 32 - Design and Construction of Frost Protected Shallow Foundations
• ASME A17.1 - Safety Code for Elevators and Escalators
• ASME A18.1 - Safety Standard for Platform Lifts and Stairway Chairlifts
• ASME A90.1 - Safety Standard for Belt Manlifts
• ASME B16.18 - Cast Copper Alloy Solder Joint Pressure Fittings
• ASME B16.22 -Wrought Copper and Copper Alloy Solder Joint Pressure Fittings
• ASME B20.1 - Safety Standard for Conveyors and Related Equipment
• ASTM A 6/A 6M - Standard Specification for General Requirements for Rolled Steel, Structural Steel Bars, Plates, Shapes, and Sheet Piling
• ASTM A 36/A 36M - Standard Specification for Carbon Structural Steel
• ASTM A 82 - Standard Specification for Steel Wire, Plain, for Concrete Reinforcement
• ASTM A 123/A 123M - Standard Specification for Zinc (Hot-Dip Galvanized) Coating on Iron and Steel Products
• ASTM A 153/A 153M - Standard Specification for Zinc Coating (Hot-Dip) on Iron and Steel Hardware
• ASTM A 167 - Standard Specification for Stainless and Heat-Resisting Chromium-Nickel Steel Plate, Sheet and Strip
• ASTM A 185 - Standard Specification for Steel Welded Wire Reinforcement, Plain for Concrete
• ASTM A 252 - Standard Specification for Welded and Seamless Steel Pipe Piles
• ASTM A 283/A 283M - Standard Specification for Low and Intermediate Tensile Strength Carbon Steel Plates
• ASTM A 307 - Standard Specification for Carbon Steel Bolts and Studs, 60,000 PSI Tensile Strength
• ASTM A 416/A 416M - Standard Specification for Steel Strand, Uncoated Seven-Wire for Prestressed Concrete
• ASTM A 421/A 421M - Standard Specification for Uncoated Stress-Relieved Steel Wire for Prestressed Concrete
• ASTM A 435/A 435M - Standard Specification for Straight-Beam Ultrasonic Examination of Steel Plates
• ASTM A 496 - Standard Specification for Steel Wire, Deformed for Concrete Reinforcement
• ASTM A 510 - Standard Specification for General Requirements for Wire Rods and Coarse Round Wire, Carbon Steel
• ASTM A 568/A 568M - Standard Specification for Steel, Sheet, Carbon, and High-Strength, Low-Alloy, Hot-Rolled and Cold-Rolled, General Requirements for
• ASTM A 572/A 572M - Standard Specification for High-Strength Low-Alloy Columbium-Vanadium Structural Steel
• ASTM A 588/A 588M - Standard Specification for High-Strength Low-Alloy Structural Steel with 50 ksi (345 Mpa) Minimum Yield Point to 4 inches (100 mm) Thick
• ASTM A 615/A 615M - Standard Specification for Deformed and Plain Billet-Steel Bars for Concrete Reinforcement
• ASTM A 641/A 641M - Standard Specification for Zinc-Coated (Galvanized) Carbon Steel Wire
• ASTM A 653/A 653M - Standard Specification for Steel Sheet, Zinc-Coated Galvanized or Zinc-Iron Alloy-Coated Galvannealed by the Hot-Dip Process
• ASTM A 706/A 706M - Standard Specification for Low-Alloy Steel Deformed and Plain Bars for Concrete Reinforcement
• ASTM A 722/A 722M - Standard Specification for Uncoated High-Strength Steel Bar for Prestressing Concrete
• ASTM A 755/A 755M - Standard Specification for Steel Sheet, Metallic-Coated by the Hot-Dip Process and Prepainted by the Coil-Coating Process for Exterior Exposed Building Products
• ASTM A 767/A 767M - Standard Specification for Zinc-Coated (Galvanized) Steel Bars for Concrete Reinforcement
• ASTM A 775/A 775M - Standard Specification for Epoxy-Coated Steel Reinforcing Bars
• ASTM A 792/A 792M - Standard Specification for Steel Sheet, 55% Aluminum-Zinc Alloy-Coated by the Hot-Dip Process
• ASTM A 875/A 875M - Standard Specification for Steel Sheet Zinc-54% Aluminum Alloy-Coated by the Hot Dip Process
• ASTM A 884 /A 884M - Standard Specification for Epoxy-Coated Steel Wire and Welded Wire Fabric for Reinforcement
• ASTM A 898/A 898M - Standard Specification for Straight Beam Ultrasonic Examination of Rolled Steel Shapes
• ASTM A 899 - Standard Specification for Steel Wire Epoxy-Coated
• ASTM A 913/A 913M - Standard Specification for High-strength Low-Alloy Steel Shapes of Structural Quality, Produced by Quenching and Self-tempering Process (QST)
• ASTM A 951 - Standard Specification for Masonry Joint Reinforcement
• ASTM A 996/A 996M - Standard Specification for Rail-Steel and Axle-Steel Deformed Bars Reinforcement for Concrete
• ASTM A1008/A 1008M - Standard Specification for Steel, Sheet, Cold-Rolled, Carbon, Structural, High-Strength Low-Alloy and High-Strength Low-Alloy with Improved Formability
• ASTM B 42 - Standard Specification for Seamless Copper Pipe, Standard Sizes
• ASTM B 43 - Standard Specification for Seamless Red Brass Pipe, Standard Sizes
• ASTM B 68M - Standard Specification for Seamless Copper Tube, Bright Annealed (Metric)
• ASTM B 88 - Standard Specification for Seamless Copper Water Tube
• ASTM B 101 - Standard Specification for Lead-Coated Copper Sheet and Strip for Building Construction
• ASTM B 209 - Standard Specification for Aluminum and Aluminum Alloy Steel and Plate
• ASTM B 251 - Standard Specification for General Requirements for Wrought Seamless Copper and Copper-Alloy Tube
• ASTM B 280 - Standard Specification for Seamless Copper Tube for Air Conditioning and Refrigeration Field Service
• ASTM B 633 - Standard Specification for Electrodeposited Coatings of Zinc on Iron and Steel
• ASTM C 5 - Standard Specification for Quicklime for Structural Purposes
• ASTM C 22/C 22M - Standard Specification for Gypsum
• ASTM C 27 - Standard Specification for Standard Classification of Fireclay and High-Alumina Refractory Brick
• ASTM C 28/C 28M - Standard Specification for Gypsum Plasters
• ASTM C 31/C 31M - Standard Practice for Making and Curing Concrete Test Specimens in the Field
• ASTM C 33 - Standard Specification for Concrete Aggregates
• ASTM C 34 - Standard Specification for Structural Clay Load-Bearing Wall Tile
• ASTM C 35 - Standard Specification for Inorganic Aggregates for Use in Gypsum Plaster
• ASTM C 36/C 36M - Standard Specification for Gypsum Wallboard
• ASTM C 37/C 37M - Standard Specification for Gypsum Lath
• ASTM C 39/C 39M - Standard Test Method for Compressive Strength of Cylindrical Concrete Specimens
• ASTM C 42/C 42M - Standard Test Method for Obtaining and Testing Drilled Cores and Sawed Beams of Concrete
• ASTM C 55 - Standard Specification for Concrete Brick
• ASTM C 56 - Standard Specification for Structural Clay Non-Load Bearing Tile
• ASTM C 59/C 59M - Standard Specification for Gypsum Casting and Molding Plaster
• ASTM C 61/C 61M - Standard Specification for Gypsum Keene's Cement
• ASTM C 62 - Standard Specification for Building Brick (Solid Masonry Units Made from Clay or Shale)
• ASTM C 67 - Standard Test Methods of Sampling and Testing Brick and Structural Clay Tile
• ASTM C 73 - Standard Specification for Calcium Silicate Face Brick (Sand-Lime Brick)
• ASTM C 79/C 79M - Standard Specification for Gypsum Sheathing Board
• ASTM C 90 - Standard Specification for Loadbearing Concrete Masonry Units
• ASTM C 91 - Standard Specification for Masonry Cement
• ASTM C 94/C 94M - Standard Specification for Ready-Mixed Concrete
• ASTM C 126 - Standard Specification for Ceramic Glazed Structural Clay Facing Tile, Facing Brick, and Solid Masonry Units
• ASTM C 140 - Standard Test Method Sampling and Testing Concrete Masonry Units and Related Units
• ASTM C 150 - Standard Specification for Portland Cement
• ASTM C 172 - Standard Practice for Sampling Freshly Mixed Concrete
• ASTM C 199 - Standard Test Method for Pier Test for Refractory Mortars
• ASTM C 206 - Standard Specification for Finishing Hydrated Lime
• ASTM C 207 - Standard Specification for Hydrated Lime for Masonry Purposes
• ASTM C 208 - Standard Specification for Cellulosic Fiber Insulating Board
• ASTM C 212 - Standard Specification for Structural Clay Facing Tile
• ASTM C 216 - Standard Specification for Facing Brick (Solid Masonry Units Made from Clay or Shale)
• ASTM C 270 - Standard Specification for Mortar for Unit Masonry
• ASTM C 315 - Standard Specification for Clay Flue Liners
• ASTM C 317/C 317M - Standard Specification for Gypsum Concrete
• ASTM C 330 - Standard Specification for Lightweight Aggregates for Structural Concrete
• ASTM C 331 - Standard Specification for Lightweight Aggregates for Concrete Masonry Units
• ASTM C 406 - Standard Specification for Roofing Slate
• ASTM C 442/C 442M - Standard Specification for Gypsum Backing Board and Coreboard and Gypsum Shaftliner Board
• ASTM C 472 - Standard Specification for Standard Test Methods for Physical Testing of Gypsum, Gypsum Plasters and Gypsum Concrete
• ASTM C 473 - Standard Test Method for Physical Testing of Gypsum Panel Products
• ASTM C 474 - Standard Test Methods for Joint Treatment Materials for Gypsum Board Construction
• ASTM C 475/C 475M - Standard Specification for Joint Compound and Joint Tape for Finishing Gypsum Wallboard
• ASTM C 476 - Standard Specification for Grout for Masonry
• ASTM C 503 - Standard Specification for Marble Dimension Stone (Exterior)
• ASTM C 514 - Standard Specification for Nails for the Application of Gypsum Board
• ASTM C 516 - Standard Specifications for Vermiculite Loose Fill Thermal Insulation
• ASTM C 547 - Standard Specification for Mineral Fiber Pipe Insulation.
• ASTM C 549 - Standard Specification for Perlite Loose Fill Insulation
• ASTM C 557 - Standard Specification for Adhesives for Fastening Gypsum Wallboard to Wood Framing
• ASTM C 568 - Standard Specification for Limestone Dimension Stone
• ASTM C 587 - Standard Specification for Gypsum Veneer Plaster
• ASTM C 588/C 588M - Standard Specification for Gypsum Base for Veneer Plasters
• ASTM C 595 - Standard Specification for Blended Hydraulic Cements
• ASTM C 615 - Standard pecification for Granite Dimension Stone
• ASTM C 616 - Standard Specification for Quartz-Based Dimension Stone
• ASTM C 618 - Standard Specification for Coal Fly Ash and Raw or Calcined Natural Pozzolan for Use as a Mineral Admixture in Concrete.
• ASTM C 629 - Standard Specification for Slate Dimension Stone
• ASTM C 630/C 630M - Standard Specification for Water-Resistant Gypsum Backing Board
• ASTM C 635 - Standard Specification for the Manufacturer, Performance, and Testing of Metal Suspension Systems for Acoustical Tile and Lay-In Panel Ceiling
• ASTM C 636 - Standard Practice for Installation of Metal Ceiling Suspension Systems for Acoustical Tile and Lay-In Panels
• ASTM C 645 - Standard Specification for Nonstructural Steel Framing Members
• ASTM C 652 - Standard Specification for Hollow Brick (Hollow Masonry Units Made from Clay or Shale)
• ASTM C 685/ C 685M - Standard Specification for Concrete Made by Volumetric Batching and Continuous Mixing
• ASTM C 744 - Standard Specification for Prefaced Concrete and Calcium Silicate Masonry Units
• ASTM C 754 - Standard Specification for Installation of Steel Framing Members to Receive Screw-attached Gypsum Panel Products
• ASTM C 836 - Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane for Use with Separate Wearing Course
• ASTM C 840 - Standard Specification for Application and Finishing of Gypsum Board
• ASTM C 841 - Standard Specification for Installation of Interior Lathing and Furring
• ASTM C 842 - Standard Specification for Application of Interior Gypsum Plaster
• ASTM C 843 - Standard Specification for Application of Gypsum Veneer Plaster
• ASTM C 844 - Standard Specification for Application of Gypsum Base to Receive Gypsum Veneer Plaster
• ASTM C 845 - Standard Specification for Expansive Hydraulic Cement
• ASTM C 847 - Standard Specification for Metal Lath
• ASTM C 887 - Standard Specification for Packaged, Dry Combined Materials for Surface Bonding Mortar
• ASTM C 897 - Standard Specification for Aggregate for Job-Mixed Portland Cement-Based Plasters
• ASTM C 926 - Standard Specification for Application of Portland Cement Based-Plaster
• ASTM C 931/C 931M - Standard Specification for Exterior Gypsum Soffit Board
• ASTM C 932 - Standard Specification for Surface-Applied Bonding Agents for Exterior Plastering
• ASTM C 933 - Standard Specification for Welded Wire Lath
• ASTM C 946 - Standard Specification for Practice for Construction of Dry-Stacked, Surface-bonded Walls
• ASTM C 954 - Standard Specification for Steel Drill Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Steel Studs from 0.033 inch (0.84 mm) to 0.112 inch (2.84 mm) in Thickness
• ASTM C 955 - Standard Specification for Load Bearing Transverse and Axial Steel Studs, Runners Tracks, and Bracing or Bridging, for Screw Application of Gypsum Panel Products and Metal Plaster Bases
• ASTM C 956 - Standard Specification for Installation of Cast-in-Place Reinforced Gypsum Concrete
• ASTM C 957 - Standard Specification for High-Solids Content, Cold Liquid-Applied Elastomeric Waterproofing Membrane with Integral Wearing Surface
• ASTM C 989 - Standard Specification for Ground Granulated Blast-Furnace Slag for Use in Concrete and Mortars
• ASTM C 1002 - Standard Specification for Steel Self-Piercing Tapping Screws for the Application of Gypsum Panel Products or Metal Plaster Bases to Wood Studs or Steel Studs
• ASTM C 1007 - Standard Specification for Installation of Load Bearing (Transverse and Axial) Steel Studs and Related Accessories
• ASTM C 1019 - Standard Test Method of Sampling and Testing Grout
• ASTM C 1029 - Standard Specification for Spray-applied Rigid Cellular Polyurethane Thermal Insulation
• ASTM C 1032 - Standard Specification for Woven Wire Plaster Base
• ASTM C 1047 - Standard Specification for Accessories for Gypsum Wallboard and Gypsum Veneer Base
• ASTM C 1063 - Standard Specification for Installation of Lathing and Furring to Receive Interior and Exterior Portland Cement Based Plaster
• ASTM C 1088 - Standard Specification for Thin Veneer Brick Units Made from Clay or Shale
• ASTM C 1157 - Standard Performance Specification for Hydraulic Cement
• ASTM C 1167 - Standard Specification for Clay Roof Tiles
• ASTM C 1177/C 1177M - Standard Specification for Glass Mat Gypsum Substrate for Use as Sheathing
• ASTM C 1178/C 1178M - Standard Specification for Glass Mat Water-Resistant Gypsum Backing Panel
• ASTM C 1186 - Standard Specification for Flat Non-Asbestos Fiber-Cement Sheets
• ASTM C 1218/ C 1218M - Standard Test Method for Water-Soluble Chloride in Mortar and Concrete
• ASTM C 1240 - Standard Specification for Silica Fume Used in Cementitious Mixtures
• ASTM C 1261 - Standard Specification for Firebox Brick for Residential Fireplaces
• ASTM C 1278/C 1278M - Standard Specification for Fiber-Reinforced Gypsum Panels
• ASTM C 1280 - Standard Specification for Application of Gypsum Sheathing
• ASTM C 1283 - Standard Practice for Installing Clay Flue Lining
• ASTM C 1314 - Standard Test Method for Compressive Strength of Masonry Prisms
• ASTM C 1328 - Standard Specification for Plastic (Stucco) Cement
• ASTM C 1329 - Standard Specification for Mortar Cement
• ASTM C 1395/C 1395M - Standard Specification for Gypsum Ceiling Board
• ASTM D 25 - Standard Specification for Round Timber Piles
• ASTM D 41 - Standard Specification for Asphalt Primer Used in Roofing, Damp Proofing and Waterproofing
• ASTM D 43 - Standard Coal Tar Primer Used in Roofing, Dampproofing and Waterproofing
• ASTM D 56 - Standard Test Method for Flash Point by Tag Closed Tester
• ASTM D 86 - Standard Test Method for Distillation of Petroleum Products at Atmospheric Pressure
• ASTM D 93 - Standard Test Method for Flash Point by Pensky-Martens Closed Cup Tester
• ASTM D 225 - Standard Specification for Asphalt Shingles (Organic Felt) Surfaced with Mineral Granules
• ASTM D 226 - Standard Specification for Asphalt-Saturated Organic Felt Used in Roofing and Waterproofing
• ASTM D 227 - Standard Specification for Coal-tar-saturated Organic Felt Used in Roofing and Waterproofing
• ASTM D 312 - Standard Specification for Asphalt Used in Roofing
• ASTM D 422 - Standard Test Method for Particle-size Analysis of Soils
• ASTM D 450 - Standard Specification for Coal-Tar Pitch Used in Roofing, Damp proofing and Waterproofing
• ASTM D 635 - Standard Test Method for Rate of Burning and/or Extent and Time of Burning of Self-Supporting Plastics in a Horizontal Position
• ASTM D 1143 - Standard Test Method for Piles under Static Axial Compressive Load
• ASTM D 1227 - Standard Specification for Emulsified Asphalt Used as a Protective Coating for Roofing
• ASTM D 1557 - Standard Test Method for Laboratory Compaction Characteristics of Soil Using Modified Effort (56,000 ft-lbf/ft3 (2,700 kN-m/m3))
• ASTM D 1586 - Standard Specification for Penetration Test and Split-barrel Sampling of Soils
• ASTM D 1761 - Standard Test Method for Mechanical Fasteners in Wood
• ASTM D 1863 - Standard Specification for Mineral Aggregate Used on Built-Up Roofs
• ASTM D 1929 - Standard Test Method for Determining Ignition Properties of Plastics
• ASTM D 1970 - Standard Specification for Self-Adhering Polymer Modified Bituminous Sheet Materials Used as Steep Roof Underlayment for Ice Dam Protection
• ASTM D 2166 - Standard Test Method for Unconfined Compressive Strength of Cohesive Soil
• ASTM D 2178 - Standard Specification for Asphalt Glass Felt Used in Roofing and Waterproofing
• ASTM D 2216 - Standard Test Method for Laboratory Determination of Water (Moisture) Content of Soil and Rock by Mass
• ASTM D 2487 - Standard Practice for Classification of Soils for Engineering Purposes (Unified Soil Classification System)
• ASTM D 2626 - Standard Specification for Asphalt Saturated and Coated Organic Felt Base Sheet Used in Roofing
• ASTM D 2822 - Standard Specification for Asphalt Roof Cement
• ASTM D 2823 - Standard Specification for Asphalt Roof Coatings
• ASTM D 2843 - Standard Test for Density of Smoke from the Burning or Decomposition of Plastics
• ASTM D 2850 - Standard Test Method for Unconsolidated, Undrained Triaxial Compression Test on Cohesive Soils
• ASTM D 2898 - Standard Test Methods for Accelerated Weathering of Fire-Retardant-Treated Wood for Fire Testing
• ASTM D 3019 - Standard Specification for Lap Cement Used with Asphalt Roll Roofing, Non Fibered, Asbestos Fibered, and Non Asbestos Fibered.
• ASTM D 3161 - Standard Test Method for a Wind Resistance of Asphalt Shingles (Fan-Induced Method)
• ASTM D 3201 - Standard Test Method for Hygroscopic Properties of Fire-Retardant Treated Wood and Wood-Based Products
• ASTM D 3278 - Standard Test Methods for Flash Point of Liquids by Small Scale Closed-Cup Apparatus
• ASTM D 3462 - Standard Specification for Asphalt Shingles Made from Glass Felt and Surfaced with Mineral Granules
• ASTM D 3468 - Standard Specification for Liquid-applied Neoprene and Chlorosulfonated Polyethylene Used in Roofing and Waterproofing
• ASTM D 3679 - Standard Specification for Rigid Poly (Vinyl Chloride) (PVC) Siding
• ASTM D 3737 - Standard Practice for Establishing Allowable Properties for Structural Glued Laminated Timber (Glulam)
• ASTM D 3746 - Standard Test Method for Impact Resistance of Bituminous Roofing Systems
• ASTM D 3747 - Standard Specification for Emulsified Asphalt Adhesive for Adhering Roof Insulation
• ASTM D 3909 - Standard Specification for Asphalt Roll Roofing (Glass Felt) Surfaced with Mineral Granules
• ASTM D 4022 - Coal Tar Roof Cement,
• ASTM D 4272 - Standard Test Method for Total Energy Impact of Plastic Films by Dart Drop
• ASTM D 4318 - Standard Test Methods for Liquid Limit, Plastic Limit, and Plasticity Index of Soils
• ASTM D 4434 - Standard Specification for Poly (Vinyl Chloride) Sheet Roofing
• ASTM D 4479 - Standard Specification for Asphalt Roof Coatings - Asbestos-Free
• ASTM D 4586 - Standard Specification for Asphalt Roof Cement, Asbestos-Free
• ASTM D 4601 - Standard Specification for Asphalt-Coated Glass Fiber Base Sheet Used in Roofing
• ASTM D 4637 - Standard Specification for EPDM Sheet Used in Single-Ply Roof Membrane
• ASTM D 4829 - Standard Test Method for Expansion Index of Soils
• ASTM D 4869 - Standard Specification for Asphalt-Saturated (Organic Felt) Organic Felt Underlayment Used in Steep Slope Roofing
• ASTM D 4897 - Standard Specification for Asphalt-Coated Glass Fiber Venting Base Sheet Used in Roofing
• ASTM D 4945 - Standard Test Method for High-Strain Dynamic Testing of Piles
• ASTM D 4990 - Standard Specification for Coal Tar Glass Felt Used in Roofing and Waterproofing
• ASTM D 5019 - Standard Specification for Reinforced Nonvulcanized Polymeric Sheet Used in Roofing Membrane
• ASTM D 5055 - Standard Specification for Establishing and Monitoring Structural Capacities of Prefabricated Wood I-Joists
• ASTM D 5456 - Standard Specification for Evaluation of Structural Composite Lumber Products
• ASTM D 5516 - Standard Test Method of Evaluating the Flexural Properties of Fire-Retardant Treated Softwood Plywood Exposed to the Elevated Temperatures
• ASTM D 5643 - Standard Specification for Coal Tar Roof Cement, Asbestos Free
• ASTM D 5664 - Standard Test Methods for Evaluating the Effects of Fire-Retardant Treatment and Elevated Temperatures on Strength Properties of Fire-Retardant Treated Lumber
• ASTM D 5665 - Standard Specification for Thermoplastic Fabrics Used in Cold-Applied Roofing and Waterproofing
• ASTM D 5726 - Standard Specification for Thermoplastic Fabrics Used in Hot-Applied Roofing and Waterproofing
• ASTM D 6083 - Standard Specification for Liquid Applied Acrylic Coating Used in Roofing
• ASTM D 6162 - Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
• ASTM D 6163 - Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Materials Using Glass Fiber Reinforcements
• ASTM D 6164 - Standard Specification for Styrene Butadiene Styrene (SBS) Modified Bituminous Sheet Metal Materials Using Polyester Reinforcements
• ASTM D 6222 - Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using Polyester Reinforcements
• ASTM D 6223 - Standard Specification for Atactic Polypropylene (APP) Modified Bituminous Sheet Materials Using a Combination of Polyester and Glass Fiber Reinforcements
• ASTM D 6298 - Standard Specification for Fiberglass Reinforced Styrene-Butadiene-Styrene (SBS) Modified Bituminous Sheets with a Factory Applied Metal Surface
• ASTM D 6305 - Standard Practice for Calculating Bending Strength Design Adjustment Factors for Fire-Retardant-Treated Plywood Roof Sheathing
• ASTM E 84 - Standard Test Method for Surface Burning Characteristics of Building Materials
• ASTM E 90 - Standard Test Method for Laboratory Measurement of Airborne Sound Transmission Loss of Building Partitions and Elements
• ASTM E 96 - Standard Test Method for Water Vapor Transmission of Materials
• ASTM E 108 - Standard Test Methods for Fire Tests of Roof Coverings
• ASTM E 119 - Standard Test Methods for Fire Tests of Building Construction and Materials
• ASTM E 136 - Standard Test Method for Behavior of Materials in a Vertical Tube Furnace at 750 Degrees C
• ASTM E 328 - Standard Methods for Stress Relaxation for Materials and Structures
• ASTM E 330 - Standard Test Method for Structural Performance of Exterior Windows, Curtain Walls, and Doors by Uniform Static Air Pressure Difference
• ASTM E 331 - Standard Test Method for Water Penetration of Exterior Windows, Skylights, Doors, and Curtain Walls by Uniform Static Air Pressure Difference
• ASTM E 492 - Standard Method for Laboratory Measurement of Impact Sound Transmission through Floor-Ceiling Assemblies Using the Tapping Machine
• ASTM E 605 - Standard Test Method for Thickness and Density of Sprayed Fire-Resistive Material (SFRM) Applied to Structural Members
• ASTM E 681 - Standard Test Methods for Concentration Limits of Flammability of Chemical (Vapors and Gases)
• ASTM E 736 - Standard Test Method for Cohesion/Adhesion of Sprayed Fire-Resistive Materials Applied to Structural Members
• ASTM E 814 - Standard Test Method for Fire Tests of Through-Penetration Fire Stops
• ASTM E 1300 - Standard Practice for Determining Load Resistance of Glass in Buildings
• ASTM E 1592 - Standard Test Method for Structural Performance of Sheet Metal Roof and Siding Systems by Uniform Static Air Pressure Difference
• ASTM E 1602 - Standard Guide for Construction of Solid Fuel-Burning Masonry Heaters
• ASTM E 1886 - Standard Test Method for Performance of Exterior Windows, Curtain Wall, Doors and Storm Shutters Impacted by Missiles and Exposed to Cyclic Pressure Differentials
• ASTM E 1966 - Standard Test Method for Fire-Resistant Joint Systems
• ASTM E 1996 - Standard Specification for Performance of Exterior Windows, Glazed Curtain Walls, Doors and Storm Shutters Impacted by Windborne Debris in Hurricanes
• ASTM F 547 - Standard Terminology of Nails for Use with Wood and Wood-Base Materials
• ASTM F 1346 - Standard Performance Specification for Safety Covers and Labeling Requirements for All Covers for Swimming Pools, Spas and Hot Tubs
• ASTM F 1667 - Standard Specification for Driven Fasteners: Nails, Spikes, and Staples
• ASTM G 152 - Standard Practice for Operating Open Flame Carbon Arc Light Apparatus for Exposure of Nonmetallic Materials
• ASTM G 154 - Standard Practice for Operating Fluorescent Light Apparatus for UV Exposure of Nonmetallic Materials
• ASTM G 155 -Standard Practice for Operating Xenon Arc Light Apparatus for Exposure of Non-Metallic Materials
• AWPA C1 - All Timber Products - Preservative Treatment by Pressure Processes
• AWPA C2 - Lumber, Timbers, Bridge Ties and Mine Ties. Preservative Treatment by Pressure Processes
• AWPA C3 - Piles - Preservative Treatment by Pressure Processes
• AWPA C4 - Poles - Preservative Treatment by Pressure Processes
• AWPA C9 - Plywood - Preservative Treatment by Pressure Processes
• AWPA C14 - Wood for Highway Construction-Preservative Treatment by Pressure Process
• AWPA C15 - Wood for Commercial-Residential Construction Preservative Treatment by Pressure Process
• AWPA C16 - Wood Used on Farms-Preservative Treatment by Pressure Processes
• AWPA C18 - Standard for Pressure Treated Material in Marine Construction
• AWPA C22 - Lumber and Plywood for Permanent Wood Foundations-Preservative Treatment by Pressure Processes
• AWPA C23 - Round Poles and Posts Used in Building Construction-Preservative Treatment by Pressure Processes
• AWPA C24 - Sawn Timber Used to Support Residential and Commercial Structures
• AWPA C28 - Standard for Preservative Treatment of Structural Glued Laminated Members and Laminations before Gluing of Southern Pine, Pacific Coast Douglas Fir, Hem Fir and Western Hemlock by Pressure Processes
• AWPA C31 - Lumber Used Out of Contact with the Ground and Continuously Protected from Liquid Water. - Treatment by Pressure Processes
• AWPA C33 - Standard for Preservative Treatment of Structural Composite Lumber by Pressure Processes
• AWPA M4 - Standard for the Care of Preservative-Treated Wood Products
• AWPA P1/P13 - Standard for Creosote Preservative
• AWPA P2 - Standard for Creosote Solution
• AWPA P5 - Standards for Waterborne Preservatives
• AWPA P8 - Standard for Oil-Borne Preservatives
• AWPA P9 - Standards for Solvents and Formulations for Organic Preservative Systems
• AWS D1.1/D1.1M - Structural Welding Code-Steel
• AWS D1.3 - Structural Welding Code-Sheet Steel
• AWS D1.4 - Structural Welding Code-Reinforcing Steel
• ANSI A156.10 - Power Operated Pedestrian Doors
• ANSI A156.19 - Power Assist and Low Energy Operated Doors
• CGSB 37-GP-56M - Standard for: Membrane, Modified Bituminous Prefabricated, and Reinforced for Roofing
• FMAPPROVAL 4450 - Approval Standard for Class 1 Insulated Steel Deck Roofs
• FMAPPROVAL 4470 - Class I Roof Covers
• FM APPROVAL 4880 - Class I Insulated Wall or Wall & Roof/Ceiling Panels; Plastic Interior Finish Materials; Plastic Exterior Building Panels; Wall/Ceiling Coating Systems; Interior or Exterior Finish Systems
• GA 216 - Application and Finishing of Gypsum Board
• GA 600 - Fire Resistance and Sound Control Design Manual
• HPVA HP-1 - For Hardwood and Decorative Plywood
• ICC/ANSI A117.1 - Accessible and Usable Buildings and Facilities
• ANSI A117.1 - Accessible and Usable Buildings and Facilities
• ICC 300 - Bleachers, Folding and Telescopic Seating, and Grandstands
• ICC IEBC - International Existing Building Code
• ICC IEC - International Electrical Code ***Provides Administrative Text to Enforce the 2002 NEC and Comply with Electrical Provisions in the Other ICC International Codes***
• ICC IECC - International Energy Conservation Code
• ICC IFC - International Fire Code
• ICC IFGC - International Fuel and Gas Code
• ICC IMC - International Mechanical Code
• ICC IPC - International Plumbing Code
• ICC IPMC - International Property Maintenance Code
• ICC IPSDC - International Private Sewage Disposal Code
• ICC IRC - International Residential Code
• ICC IUWIC - International Urban-Wildland Interface Code
• NAAMM FP 1001 - Guide Specifications for Design of Metal Flagpoles
• NFPA 11 - Standard for Low-, Medium-, and High-Expansion Foam
• NFPA 11A - Medium- and High-expansion Foam Systems
• NFPA 12 - Carbon Dioxide Extinguishing Systems
• NFPA 12A - Halon 1301 Fire Extinguishing Systems
• NFPA 13 - Installation of Sprinkler System
• NFPA 13D - Installation of Sprinkler Systems in One- and Two-Family Dwellings and Manufactured Home
• NFPA 13R - Installation of Sprinkler Systems in Residential Occupancies Up to and Including Four Stories in Height
• NFPA 14 - Installation of Standpipe, Private Hydrants and Hose System
• NFPA 16 - Installation Foam-Water Sprinkler and Foam-Water Spray Systems
• NFPA 17 - Dry Chemical Extinguishing Systems
• NFPA 17A - Wet Chemical Extinguishing System
• NFPA 30 - Flammable and Combustible Liquids Code
• NFPA 32 - Drycleaning Plants
• NFPA 40 - Storage and Handling of Cellulose Nitrate Motion Picture Film
• NFPA 61 - Prevention of Fires and Dust Explosions in Agricultural and Food Product Facilities
• NFPA 72 - National Fire Alarm Code
• NFPA 80 - Fire Doors and Fire Windows
• NFPA 85 - Boiler and Combustion System Hazards Code (Note: NFPA 8503 has been incorporated into NFPA 85)
• NFPA 101 - Life Safety Code
• NFPA 111 - Stored Electrical Energy Emergency and Standby Power Systems
• NFPA 120 - Standard for Fire Prevention and Control in Coal Mines
• NFPA 252 - Standard Methods of Fire Tests of Door Assemblies
• NFPA 253 - Test for Critical Radiant Flux of Floor Covering Systems Using a Radiant Heat Energy Source
• NFPA 257 - Standard for Fire Test for Window and Glass Block Assemblies
• NFPA 259 - Test Method for Potential Heat of Building Materials
• NFPA 265 - Standard Methods of Fire Tests for Evaluating Room Fire Growth Contribution of Textile Coverings on Full Height Panels and Walls
• NFPA 268 - Standard Test Method for Determining Ignitibility of Exterior Wall Assemblies Using a Radiant Heat Energy Source
• NFPA 285 - Flammability Characteristics of Exterior Nonload Bearing Wall Assemblies Containing Combustible Components Using the Intermediate Scale Multi-Story Test Apparatus
• NFPA 286 - Methods for Fire Tests for Evaluating Contribution of Wall and Ceiling Interior Finish to Room Fire Growth
• NFPA 409 - Standard on Aircraft Hangers
• NFPA 418 - Heliports
• NFPA 654 -Standard for the Prevention of Fire & Dust Explosions from the Manufacturing, Processing, and Handling of Combustible Particulate Solids
• NFPA 655 - Prevention of Sulfur Fires and Explosions
• NFPA 664 - Standard for the Prevention of Fires Explosions in Wood Processing and Woodworking Facilities
• NFPA 701 - Standard Methods of Fire Tests for Flame-Propagation of Textiles and Films
• NFPA 704 - Standard System for the Identification of the Hazards of Materials for Emergency Response
• NFPA 1124 - Code for the Manufacture, Transportation, Storage, and Retail Sales of Fireworks and Pyrotechnic Articles
• RMA RP-2 - Minimum Requirements for Fabric-Reinforced Black EPDM Rubber Sheets
• TIA-222 - Structural Standards for Steel Antenna Towers and Antenna Supporting Structures
• TPI 1 - National Design Standard for Metal Plate Connected Wood Truss Construction
• UL 10A - Tin-Clad Fire Doors
• UL 10B - Fire Tests of Door Assemblies
• UL 10C - Positive Pressure Fire Tests of Door Assemblies
• UL 14B - Sliding Hardware for Standard, Horizontally Mounted Tin Clad Fire Doors
• UL 14C - Swinging Hardware for Standard Tin-Clad Fire Doors Mounted Singly and in Pairs
• UL 103 - Factory-Built Chimneys, for Residential Type and Building Heating Appliances
• UL 127 - Factory-Built Fireplaces
• UL 268 - Smoke Detectors for Fire Protective Signaling Systems
• UL 300 - Fire Testing of Fire Extinguishing Systems for Protection of Restaurant Cooking Areas
• UL 555 - Fire Dampers
• UL 555C - Ceiling Dampers
• UL 555S - Smoke Dampers
• UL 580 - Test for Uplift Resistance of Roof Assemblies
• UL 641 - Low-Temperature Venting Systems, Type L
• UL 790 - Test Methods for Fire Resistance of Roof Covering Materials
• UL 864 - Control Units for Fire Protective Signaling Systems
• UL 1040 - Fire Test of Insulated Wall Construction
• UL 1256 - Fire Test of Roof Deck Construction
• UL 1479 - Fire Tests of Through-Penetration Firestops
• UL 1715 - Fire Test of Interior Finish Material
• UL 1777 - Chimney Liners
• UL 1784 - Air Leakage Tests of Door Assemblies
• UL 1897 - Uplift Tests for Roof Covering Systems
• UL 1975 - Fire Tests for Foamed Plastics Used for Decorative Purposes
• UL 2079 - Tests for Fire Resistance of Building Joint Systems
• UL 2200 - Stationary Engine Generator Assemblies